Saturday 11 April 2015

Block diagram of AM transmitter and receiver with explanation

Block diagram of AM transmitter and receiver with explanation
AM Transmitter :
Transmitters that transmit AM signals are known as AM transmitters. These transmitters are used in medium wave (MW) and short wave (SW) frequency bands for AM broadcast. The MW band has frequencies between 550 KHz and 1650 KHz, and the SW band has frequencies ranging from 3 MHz to 30 MHz. The two types of AM transmitters that are used based on their transmitting powers are:
·         High Level
·         Low Level
High level transmitters use high level modulation, and low level transmitters use low level modulation. The choice between the two modulation schemes depends on the transmitting power of the AM transmitter. In broadcast transmitters, where the transmitting power may be of the order of kilowatts, high level modulation is employed. In low power transmitters, where only a few watts of transmitting power are required , low level modulation is used.
High-Level and Low-Level Transmitters                                                                                       
Below figure's show the block diagram of high-level and low-level transmitters. The basic difference between the two transmitters is the power amplification of the carrier and modulating signals.
Figure (a) shows the block diagram of high-level AM transmitter.


 In high-level transmission, the powers of the carrier and modulating signals are amplified before applying them to the modulator stage, as shown in figure (a). In low-level modulation, the powers of the two input signals of the modulator stage are not amplified. The required transmitting power is obtained from the last stage of the transmitter, the class C power amplifier.
The various sections of the figure (a) are:
·         Carrier oscillator
·         Buffer amplifier
·         Frequency multiplier
·         Power amplifier
·         Audio chain
·         Modulated class C power amplifier
Carrier oscillator
The carrier oscillator generates the carrier signal, which lies in the RF range. The frequency of the carrier is always very high. Because it is very difficult to generate high frequencies with good frequency stability, the carrier oscillator generates a sub multiple with the required carrier frequency. This sub multiple frequency is multiplied by the frequency multiplier stage to get the required carrier frequency. Further, a crystal oscillator can be used in this stage to generate a low frequency carrier with the best frequency stability. The frequency multiplier stage then increases the frequency of the carrier to its required value.
Buffer Amplifier                                                
The purpose of the buffer amplifier is two fold. It first matches the output impedance of the carrier oscillator with the input impedance of the frequency multiplier, the next stage of the carrier oscillator. It then isolates the carrier oscillator and frequency multiplier.
This is required so that the multiplier does not draw a large current from the carrier oscillator. If this occurs, the frequency of the carrier oscillator will not remain stable.
Frequency Multiplier                                                
The sub-multiple frequency of the carrier signal, generated by the carrier oscillator , is now applied to the frequency multiplier through the buffer amplifier. This stage is also known as harmonic generator. The frequency multiplier generates higher harmonics of carrier oscillator frequency. The frequency multiplier is a tuned circuit that can be tuned to the requisite carrier frequency that is to be transmitted.

Power Amplifier
The power of the carrier signal is then amplified in the power amplifier stage. This is the basic requirement of a high-level transmitter. A class C power amplifier gives high power current pulses of the carrier signal at its output.
Audio Chain
The audio signal to be transmitted is obtained from the microphone, as shown in figure (a). The audio driver amplifier amplifies the voltage of this signal. This amplification is necessary to drive the audio power amplifier. Next, a class A or a class B power amplifier amplifies the power of the audio signal.
Modulated Class C Amplifier                                                             
This is the output stage of the transmitter. The modulating audio signal and the carrier signal, after power amplification, are applied to this modulating stage. The modulation takes place at this stage. The class C amplifier also amplifies the power of the AM signal to the reacquired transmitting power. This signal is finally passed to the antenna., which radiates the signal into space of transmission.
Figure  shows the block diagram of a low-level AM transmitter.

The low-level AM transmitter shown in the figure (b) is similar to a high-level transmitter, except that the powers of the carrier and audio signals are not amplified. These two signals are directly applied to the modulated class C power amplifier.
Modulation takes place at the stage, and the power of the modulated signal is amplified to the required transmitting power level. The transmitting antenna then transmits the signal.



AM Receiver :

The basic block diagram of a basic superhet receiver is shown below. This details the most basic form of the receiver and serves to illustrate the basic blocks and their function.

Block diagram of a basic superheterodyne radio receiver
The way in which the receiver works can be seen by following the signal as is passes through the receiver.

  • Front end amplifier and tuning block:   Signals enter the front end circuitry from the antenna. This circuit block performs two main functions:
    • Tuning:   Broadband tuning is applied to the RF stage. The purpose of this is to reject the signals on the image frequency and accept those on the wanted frequency. It must also be able to track the local oscillator so that as the receiver is tuned, so the RF tuning remains on the required frequency. Typically the selectivity provided at this stage is not high. Its main purpose is to reject signals on the image frequency which is at a frequency equal to twice that of the IF away from the wanted frequency. As the tuning within this block provides all the rejection for the image response, it must be at a sufficiently sharp to reduce the image to an acceptable level. However the RF tuning may also help in preventing strong off-channel signals from entering the receiver and overloading elements of the receiver, in particular the mixer or possibly even the RF amplifier.
    • Amplification:   In terms of amplification, the level is carefully chosen so that it does not overload the mixer when strong signals are present, but enables the signals to be amplified sufficiently to ensure a good signal to noise ratio is achieved. The amplifier must also be a low noise design. Any noise introduced in this block will be amplified later in the receiver.
  • Mixer / frequency translator block:   The tuned and amplified signal then enters one port of the mixer. The local oscillator signal enters the other port. The performance of the mixer is crucial to many elements of the overall receiver performance. It should eb as linear as possible. If not, then spurious signals will be generated and these may appear as 'phantom' received signals.
  • Local oscillator:   The local oscillator may consist of a variable frequency oscillator that can be tuned by altering the setting on a variable capacitor. Alternatively it may be a frequency synthesizer that will enable greater levels of stability and setting accuracy.
  • Intermediate frequency amplifier, IF block :   Once the signals leave the mixer they enter the IF stages. These stages contain most of the amplification in the receiver as well as the filtering that enables signals on one frequency to be separated from those on the next. Filters may consist simply of LC tuned transformers providing inter-stage coupling, or they may be much higher performance ceramic or even crystal filters, dependent upon what is required.
  • Detector / demodulator stage:   Once the signals have passed through the IF stages of the superheterodyne receiver, they need to be demodulated. Different demodulators are required for different types of transmission, and as a result some receivers may have a variety of demodulators that can be switched in to accommodate the different types of transmission that are to be encountered. Different demodulators used may include:


    • AM diode detector:   This is the most basic form of detector and this circuit block would simple consist of a diode and possibly a small capacitor to remove any remaining RF. The detector is cheap and its performance is adequate, requiring a sufficient voltage to overcome the diode forward drop. It is also not particularly linear, and finally it is subject to the effects of selective fading that can be apparent, especially on the HF bands.
    • Synchronous AM detector:   This form of AM detector block is used in where improved performance is needed. It mixes the incoming AM signal with another on the same frequency as the carrier. This second signal can be developed by passing the whole signal through a squaring amplifier. The advantages of the synchronous AM detector are that it provides a far more linear demodulation performance and it is far less subject to the problems of selective fading.
    • SSB product detector:   The SSB product detector block consists of a mixer and a local oscillator, often termed a beat frequency oscillator, BFO or carrier insertion oscillator, CIO. This form of detector is used for Morse code transmissions where the BFO is used to create an audible tone in line with the on-off keying of the transmitted carrier. Without this the carrier without modulation is difficult to detect. For SSB, the CIO re-inserts the carrier to make the modulation comprehensible.
    • Basic FM detector:   As an FM signal carries no amplitude variations a demodulator block that senses frequency variations is required. It should also be insensitive to amplitude variations as these could add extra noise. Simple FM detectors such as the Foster Seeley or ratio detectors can be made from discrete components although they do require the use of transformers.
    • PLL FM detector:   A phase locked loop can be used to make a very good FM demodulator. The incoming FM signal can be fed into the reference input, and the VCO drive voltage used to provide the detected audio output.
    • Quadrature FM detector:   This form of FM detector block is widely used within ICs. IT is simple to implement and provides a good linear output.
  • Audio amplifier:   The output from the demodulator is the recovered audio. This is passed into the audio stages where they are amplified and presented to the headphones or loudspeaker

13 comments:

  1. simple and satisfying explanation

    ReplyDelete
  2. very satisfying explaination

    ReplyDelete
  3. Nice. You give very brief information on transmitter and receiver

    ReplyDelete
  4. Nice, You give brief information on transmitter and receiver.

    ReplyDelete
  5. Manufactures of Automatic water level controller and Indicator in Chennai and Tamilnadu, wireless water tank level indicator and wireless water level controller in Chennai, OMR, Anna Nagar, Velachery

    ReplyDelete
  6. With a Wireless Signal Video Transmitter, you can enjoy your favourite videos from any
    corner of the room up to 1000 ft without compromising on quality. Tv channel solution provide
    these types of products at best price with lifetime support.

    ReplyDelete